Practical tutorial for injection mold design. For example, the weight of the product is not large, but the projection surface is large. Then consider the number of molds. Look at the book step by step. In the case of the special case, the formwork is smaller.. This will result in large injection cost and reduced profit for the manufacturer. Injection Mold Design. Analyze the material port, first select the feed side. The product is on the mold. These are necessary.Plastic mold structure analysis
To analyze the structure of plastic molds, we must first understand whether the products have the conditions for mold opening, whether there are drafting, excessive wall thickness, shrinkage deformation, undercut and other factors affecting the mold, and understand the shrinkage rate and fluidity of the product materials. Guangzhou: South China University of Technology Press, ’Plastic Mold Technical Manual’ Editorial Board, Plastic Mold Technical Manual. Beijing: Mechanical Industry Press. After the front and rear molds are determined, the position of the parting surface of the product is determined. Beijing: Beijing Institute of Technology. (I think: first choose the mold material according to the quantity of the product. Zhang Wei Including. However, the curriculum design is not preform mould https://www.pet-mould.com/product/preform-mould/ too complicated, and all the steps are all right. But I don’t know what your plastic parts look like. The position of the runner, the runner gate, the position of the jack, the position of the cooling water, the size of the front and rear molds, and finally the size of the mold base. . I have set up to do plastic mold design, recommend a few books for you, certainly useful: Wang Shuxun, Zhu Yalin, Mei Wei, Long Guoliang. In addition, we must design the core, the launch mechanism or something. Beijing: Chemical Industry Press 3. Concise Plastic Mold Design Handbook.
After the position of the mold gate and the runner, and the relevant information about the product structure and materials, the next step is to determine the front and back molds of the product. If the plastic parts are very simple, just design them just fine.) Supplement: There are mainly the choice of parting surface, the choice of gate location, etc. Then consider the cooling water position, the position of the top rod, the position of the fixing screw, the position of the reset rod Finally, the size of the formwork and the thickness of the formwork are determined. Qi Weidong
To analyze the structure of plastic molds, we must first understand whether the products have the conditions for mold opening, whether there are drafting, excessive wall thickness, shrinkage deformation, undercut and other factors affecting the mold, and understand the shrinkage rate and fluidity of the product materials. Guangzhou: South China University of Technology Press, ’Plastic Mold Technical Manual’ Editorial Board, Plastic Mold Technical Manual. Beijing: Mechanical Industry Press. After the front and rear molds are determined, the position of the parting surface of the product is determined. Beijing: Beijing Institute of Technology. (I think: first choose the mold material according to the quantity of the product. Zhang Wei Including. However, the curriculum design is not preform mould https://www.pet-mould.com/product/preform-mould/ too complicated, and all the steps are all right. But I don’t know what your plastic parts look like. The position of the runner, the runner gate, the position of the jack, the position of the cooling water, the size of the front and rear molds, and finally the size of the mold base. . I have set up to do plastic mold design, recommend a few books for you, certainly useful: Wang Shuxun, Zhu Yalin, Mei Wei, Long Guoliang. In addition, we must design the core, the launch mechanism or something. Beijing: Chemical Industry Press 3. Concise Plastic Mold Design Handbook.
After the position of the mold gate and the runner, and the relevant information about the product structure and materials, the next step is to determine the front and back molds of the product. If the plastic parts are very simple, just design them just fine.) Supplement: There are mainly the choice of parting surface, the choice of gate location, etc. Then consider the cooling water position, the position of the top rod, the position of the fixing screw, the position of the reset rod Finally, the size of the formwork and the thickness of the formwork are determined. Qi Weidong
コメント